3 Axles Side Wall Semi Trailer-manufacture,factory,supplier from China

1. ChassisThe frame is mainly composed of girder - welded I-beam, support beam, connection beam, side beam, lock, traction pin connection device, panel, etc.The side beams are generally channel steel or bending pieces. At present, most trailers use channel steel. There will be more side beams for bending pieces with light body, because the requirements for strength are not too large.The supporting beam is the crossing beam, and now most of them are W beams. 2.  Upper bodyFor side wall trailers, the bodywork part refers to railings, gantries, etc.

Fence semi trailer is a relatively common means of cargo transportation, with a wide range of types and uses.According to the regulations, the height of the fence truck trailer shall not exceed 4.2 meters. According to the regulations, the loading height of heavy and medium-sized trucks and semi-trailers shall not exceed 4 meters from the ground, and the vehicle carrying containers shall not exceed 4.2 meters. Semi trailers are mostly 3 axles trailers, which are connected with semi-trailers through front traction pins.

1. Early wear of the central part of the tire.The main reason is that the tire inflation volume is too large, which not only affects the shock absorption performance of the tire, but also causes excessive deformation of the tire.2. Both sides of the tire are worn too much.The main reason: insufficient inflation of the tire or long-term overload driving, so that the contact surface between the tire and the ground is large, causing the two sides of the tire to contact the ground and form early wear.3.

1. Pipeline laying and installationA. Arrange the pipeline reasonably according to the vehicle model. The long pipe shall be connected with the air storage tank of the rear relay valve. The length shall be appropriate and shall not be too loose or tight. The pipe clamp shall be locked on the thread clamp screw on the right side of the longitudinal dye. The thread clamp shall not be missed.

To measure a trailer axle, first, you need to identify the type of trailer axle. There are two types of trailer axles, including the straight axle and drop axle. The straight axle is mounted directly below the trailer deck, while the drop axle is mounted a few inches below the trailer deck.Here are the steps to measure a trailer axle:Measure the length of the axle from one end to the other. You can use a tape measure for this.Determine the weight capacity of the axle.

Semi trailers are widely used and cannot be replaced by ordinary vehicles. Almost all materials can be completed by semi trailers. Now let's take a look at the production process of semi-trailer.

The details of the maintenance of the dump semi trailer should be paid attention to. Safe driving is very important for the dump semi trailer. In order to prevent problems in the future, the dump semi trailer should be regularly checked and maintained. Maintenance details of self-dumping semi-trailer: First, check whether there is a lack of air, debris attachment and other phenomena, whether the steel ring deformation, cracks and other phenomena.

Master the correct driving method of the dump semi-trailer, the dump semi-trailer in the unloading of the car is rollover or back, we usually drive the dump semi-trailer, we must master the correct driving mode, dump semi-trailer manufacturers to introduce. 1. First of all, when the dump semi-trailer starts, pay attention not to use too much throttle, clutch can not be violently lifted and put, the start must be stable. 2. Avoid some bad driving habits, such as putting your hand on the stop rod for a long time, which will affect the safety of driving and damage the gearbox.

1. Introduction the present situationWith the improvement of the highway and its infrastructure and the rapid development of the national economy, the demand for semi-trailer with high transport efficiency is growing rapidly in recent years.Among the components of the semi-trailer, the tire is the only component of the vehicle that directly contacts the road surface.

First of all, the semi-trailer should do a systematic test during the running-in period to see whether the connection with the host is correct and safe and reliable, check whether there is any problem with the braking system, whether the tire pressure of the semi-trailer meets the standard, and check whether the various parts of the semi-trailer are loose, cracked and deformed.Subsequently, the load of the semi-trailer during the running-in period cannot exceed 80% of the rated load weight; During medium-speed driving, pay attention to the temperature of bearings and hubs.