2 axle Tipper Trailer-manufacture,factory,supplier from China

To measure a trailer axle, first, you need to identify the type of trailer axle. There are two types of trailer axles, including the straight axle and drop axle. The straight axle is mounted directly below the trailer deck, while the drop axle is mounted a few inches below the trailer deck.Here are the steps to measure a trailer axle:Measure the length of the axle from one end to the other. You can use a tape measure for this.Determine the weight capacity of the axle.

Changing the hydraulic oil looks like a simple job, but many friends of the driver of the rear-turning semi-trailer do not know how to change it correctly. They often mix the new and old hydraulic oil, which will greatly reduce the service life of the hydraulic system. So how to change the hydraulic oil of the rear tipper semi-trailer? Are there any precautions?The traditional method of replacing hydraulic oil for rear dump semi-trailer is nothing more than extracting the hydraulic oil from the hydraulic oil tank, replacing the hydraulic oil filter element, and then adding new hydraulic oil.

1. Early wear of the central part of the tire.The main reason is that the tire inflation volume is too large, which not only affects the shock absorption performance of the tire, but also causes excessive deformation of the tire.2. Both sides of the tire are worn too much.The main reason: insufficient inflation of the tire or long-term overload driving, so that the contact surface between the tire and the ground is large, causing the two sides of the tire to contact the ground and form early wear.3.

1. ChassisThe frame is mainly composed of girder - welded I-beam, support beam, connection beam, side beam, lock, traction pin connection device, panel, etc.The side beams are generally channel steel or bending pieces. At present, most trailers use channel steel. There will be more side beams for bending pieces with light body, because the requirements for strength are not too large.The supporting beam is the crossing beam, and now most of them are W beams. 2.  Upper bodyFor side wall trailers, the bodywork part refers to railings, gantries, etc.

Master the correct driving method of the dump semi-trailer, the dump semi-trailer in the unloading of the car is rollover or back, we usually drive the dump semi-trailer, we must master the correct driving mode, dump semi-trailer manufacturers to introduce. 1. First of all, when the dump semi-trailer starts, pay attention not to use too much throttle, clutch can not be violently lifted and put, the start must be stable. 2. Avoid some bad driving habits, such as putting your hand on the stop rod for a long time, which will affect the safety of driving and damage the gearbox.

1. Standard Flatbed Trailer: This is the most common type of flatbed trailer. It has a basic design with a flat, open platform that allows for the transportation of a wide variety of cargo. It is typically equipped with stake pockets and tie-down points for securing the load.2. Drop Deck Trailer: Also known as a lowboy or step deck trailer, the drop deck trailer has a lower deck height than a standard flatbed trailer. This allows for the transportation of taller cargo that cannot fit within the height restrictions of a standard trailer.

The capacity of a semi tanker trailer can vary depending on the size and configuration of the trailer. However, a typical semi tanker trailer can hold around 7,000 to 9,000 gallons of liquid, but some larger tanker trailers can hold up to 11,000 gallons or more.

The lifespan of a semi trailer depends on various factors, including usage, maintenance, operating conditions, and the quality of the trailer. Generally, a well-maintained semi trailer can last anywhere between 10 to 15 years.Regular maintenance and inspections are crucial to ensure the longevity of the trailer. Components such as tires, brakes, suspension, and electrical systems should be regularly checked and replaced as needed.

We should also pay attention to some problems when using the skeleton semi trailer, although its operation is simple, although the skeleton trailer is large, but the operation is not so complicated, what needs our attention is the correct driving. First, the skeleton truck trailer fully considers the use of the operator's feelings, because the workers are usually very hard, and the environment is not good, which requires the skeleton trailer to provide the user with comfort as much as possible, assist direction, comfortable seats, open vision, simple and practical buttons, many things

As an engineering vehicle, the dump trailer drives the hydraulic mechanism through the engine of the dump trailer, and then drives the lifting mechanism to complete the tilting action to achieve the purpose of unloading. When the unloading is completed, it will reset. So, what are the advantages of the rear dump trailer?The rear dump trailer has the characteristics of low center of gravity and difficult to overturn when lifting. The frame is made of 16 manganese beam plates, which greatly increases the bearing strength.