2 Axle Fuel Tank Semi Trailer-manufacture,factory,supplier from China

To measure a trailer axle, first, you need to identify the type of trailer axle. There are two types of trailer axles, including the straight axle and drop axle. The straight axle is mounted directly below the trailer deck, while the drop axle is mounted a few inches below the trailer deck.Here are the steps to measure a trailer axle:Measure the length of the axle from one end to the other. You can use a tape measure for this.Determine the weight capacity of the axle.

The amount of fuel tanker trailer can hold varies depending on its size and capacity. Standard tanker trailers can carry around 9,000 to 11,000 gallons of fuel, while larger models can hold up to 13,000 gallons or more. It's important to note that the maximum amount of fuel a tanker trailer can carry is regulated by transport laws and safety measures.

Changing the hydraulic oil looks like a simple job, but many friends of the driver of the rear-turning semi-trailer do not know how to change it correctly. They often mix the new and old hydraulic oil, which will greatly reduce the service life of the hydraulic system. So how to change the hydraulic oil of the rear tipper semi-trailer? Are there any precautions?The traditional method of replacing hydraulic oil for rear dump semi-trailer is nothing more than extracting the hydraulic oil from the hydraulic oil tank, replacing the hydraulic oil filter element, and then adding new hydraulic oil.

Master the correct driving method of the dump semi-trailer, the dump semi-trailer in the unloading of the car is rollover or back, we usually drive the dump semi-trailer, we must master the correct driving mode, dump semi-trailer manufacturers to introduce. 1. First of all, when the dump semi-trailer starts, pay attention not to use too much throttle, clutch can not be violently lifted and put, the start must be stable. 2. Avoid some bad driving habits, such as putting your hand on the stop rod for a long time, which will affect the safety of driving and damage the gearbox.

1. Early wear of the central part of the tire.The main reason is that the tire inflation volume is too large, which not only affects the shock absorption performance of the tire, but also causes excessive deformation of the tire.2. Both sides of the tire are worn too much.The main reason: insufficient inflation of the tire or long-term overload driving, so that the contact surface between the tire and the ground is large, causing the two sides of the tire to contact the ground and form early wear.3.

1. ChassisThe frame is mainly composed of girder - welded I-beam, support beam, connection beam, side beam, lock, traction pin connection device, panel, etc.The side beams are generally channel steel or bending pieces. At present, most trailers use channel steel. There will be more side beams for bending pieces with light body, because the requirements for strength are not too large.The supporting beam is the crossing beam, and now most of them are W beams. 2.  Upper bodyFor side wall trailers, the bodywork part refers to railings, gantries, etc.

When there is an electrical fault in the oil tank trailer, it is an important prerequisite for maintenance to quickly and accurately judge the fault. After a lot of practice and research for a long time, the maintenance engineers have realized that the following methods are very practical in electrical diagnosis.Observation methodIf the starter of the ofuel tanker trailer cannot be started, turn on the headlight first, observe its brightness, and judge whether the fault is caused by poor contact of the power line or battery power loss.

1. Pipeline laying and installationA. Arrange the pipeline reasonably according to the vehicle model. The long pipe shall be connected with the air storage tank of the rear relay valve. The length shall be appropriate and shall not be too loose or tight. The pipe clamp shall be locked on the thread clamp screw on the right side of the longitudinal dye. The thread clamp shall not be missed.

The cost of a semi truck trailer can vary depending on the type, size, and features of the trailer. On average, a new semi truck trailer can cost anywhere from $8,000 to $60,000 or more. However, there are used trailers available for sale at a lower price range, typically starting from around $5,000 to $20,000. It's also important to consider additional costs such as insurance, maintenance, and fuel expenses when purchasing a semi truck trailer.

Semi trailers are widely used and cannot be replaced by ordinary vehicles. Almost all materials can be completed by semi trailers. Now let's take a look at the production process of semi-trailer.